What Have You Done To Your Van Today?

[Kind of Blue]

Very proficient and very fast work! Its a pity that the VW Badges could not be removed completely to leave just the grill. I would be still looking for the lost parts, clips and screws in the grass. I hope that these live up to expectation for you. Be seeing you!

 

[spooks007]

Fixed this morning

Before



After

 

[dhardyuk]

Busy morning all ready, fitted the LED headlights from THQ, time for a coffee before washing the van.

Just out of interest ….. do you have to set the beam pattern up or do the lamps come preset with the angles etc configured ready to go?

 

[DaveJH]

Just out of interest ….. do you have to set the beam pattern up or do the lamps come preset with the angles etc configured ready to go?

From what I have read I don’t need to do anything they are pre-configured. However I will be checking them out when it gets dark just to make sure.

 

[Skyliner33]

Well another visit to the House of @Dav-Tec ANOTHER full day but finally got it up and running. Thanks again Chris. You're a wizard mate.
View attachment 285391View attachment 285392View attachment 285393View attachment 285394View attachment 285395View attachment 285396View attachment 285397View attachment 285398

Thanks good. I wish mine had a better headunit.

 

[dcpen43]

Just had a go with my new polishing wheel on the Van. Thought i had a reflection of Elvis at the back for a minute

 

[T6Plumber]

Finally got around to fitting my new steering wheel & airbag cover to match the rest of the Black & Grey cab theme

 

[Vinyl1210]

Fitted an additional bracket in the sliding door footwell as an alternative to the usual ‘B Pillar Ovano Table’ (which I do like by the way but thought this was a much better alternative in my situation as I already have the table set up for a bracket between the rear side storage/benches). Cheaper by far (£22 ish for bracket). £2:50 for size 6 x20 mm screws from B&Q.
Ideal for putting laptop, test gear and a brew when out on site, a beer & sarnie when chilling or ……. All of the above.
Enjoy the BH peeps. Edit for spellcheck
Further Edit to say (incase someone is thinking of it, unfortunately you cannot close the slider with table leg in place as not quite enough clearance. (Which I believe is advantage of Ovano offering), however suits my requirements perfectly. Cheers.

 

[Brennanpj]

nearly finished my interior, got the bench seat back in today after 2 months .

 

[Snakelimit]

nearly finished my interior, got the bench seat back in today after 2 months . View attachment 285589View attachment 285590View attachment 285591View attachment 285592View attachment 285593

What is that sliding mechanism? Need something like that in mine

 

[Brennanpj]

What is that sliding mechanism? Need something like that in mine

Caravelle rails & seats

 

[T6Plumber]

Gave the van a big clean & changed my recently bought 4D number plates for some pressed metal ones. I felt the 4D was a little bit too much. Loads happier with these ones.

 

[twotone2]

Gave the van a big clean & changed my recently bought 4D number plates for some pressed metal ones. I felt the 4D was a little bit too much. Loads happier with these ones.

View attachment 285606

View attachment 285605

Got pressed metal plates on my van and MX5, think all number plates should be!

 

[Johny]

Got pressed metal plates on my van and MX5, think all number plates should be!

Look great don't they?
If only they were legal.

 

[Snakelimit]

Caravelle rails & seats

Just see the price for them I might do something myself

 

[Bav]

Look great don't they?
If only they were legal.

Are you referring to the specific plates pictured or to pressed plates in general?
Like all reg plates, they need to meet conform to certain requirements, but pressed plates aren't intrinsically illegal.

 

[JumpShip]

Our pressed plates are 100% legal

 

[T6ARF]

Our pressed plates are 100% legal

Mine too!

 

[T6Plumber]

Mine too!

Yep. Totally legal

 

[Johny]

Are you referring to the specific plates pictured or to pressed plates in general?
Like all reg plates, they need to meet conform to certain requirements, but pressed plates aren't intrinsically illegal.

As I see it any vehicle after 2001 isn't supposed to carry pressed plates, and since 2021 plates are supposed to be able to spring back into shape after a knock, pressed plates can't do this.