step

Does anybody know whether it's possible to get an oem Kombi side step without the light (or any opening) at one end? Thanks

Hi all Just sticking some bits and pieces to van and one door sill hasn't stuck very well. The bottom is ok but top (either side) not very good, can anyone suggest best way to secure down as don't want to buy anything that might make hard to remove at later date if required Thanks

Hi, Im sure plenty of you have done it. Any advice on removing the drivers side interior step? I’m just replacing it as it’s abit worn and doesn’t look very nice. Iv got trim removal tools so is it just a case of removing the door seal out the way & then pop out the trim or is it more long...

Hoping somebody can help, I have been online for what seems like an eternity and cant find or establish what part number I need to order a new offside front drivers step with heater grill and factory light cutout in satin black 9B9 - 82V. Also need the part number for a new nearside front...

Read a few threads on this but would like to hear from anyone who has swapped the standard side step to a kombi one. I've got non slip phenolic plywood for my floor which will sit on a mixture of 9mm spacers and the metal ribs of the floor. Will the kombi step work with 12mm ply only? No top...

can anyone tell me if this is still available if they have access to the up to date parts catalogue if possible? step in satin black with grill...no light.. regards chris

Well my vanstyle raised step doesn’t seem to fit with my 12mm ply floor, the bottom section doesnt sit on the base metal... although the rear piece fits perfectly. Any ideas on which others I should be looking at that would fit? It’s for a pannel van, ply sitting on top of the metal ridges...

trying to locate one of these for my diesel heater fit... im going to put the norm round rear piece in from the non genuine ducting...(non gen 65mm jobby) ...but use this step as looks far nicer..I think there should be enough room behind for the base circular piece to hide behind.

Brand new still in wrapping - bought to use when fitting night heater but decided not to use in the end. £40 + p&p or can collect from Grimsby area.

Hi All, Looking for guidance - I have a T6 panel van which I've lined... I've added some 6mm dodo superliner to the floor, along with around 30% coverage of silent coat below that. I've just picked up a genuine VW rubber insulated floor, which I've now added above this (As per a kombi floor...

Hi Guys Im looking for 2015 T5 Drivers side (and passenger if available) Plastic door steps and also a drivers side air vent assembly - the old one has a hole cut in it and all me change is disappearing into the dashboard when I go round corners . Thanks Matt

Is there available the side steps for the sliding doors without any lights and suitable for a factory kombi (rubber) flooring height??

Hi all, so I’ve fitted my floor and the side step I bought from van style is way off. so I’ve used 9mm batons between and round the ridges 6mm insulation mat (probably less when compressed, 12mm ply 2mm altro so that’s a total of 29mm from the original which sat on the metal (was a pannel...

Hi Guys, How do I get the front and side instep out ? or is there something on the web site.

As above .... thanks ;)

Hi all, I'd like to to install a courtesy footwell light or side bar lights for the side entrance to my t6 camper, my Highline doesn't have anything in place. Can someone advise where I'd get the feed from? I've installed footwell lights from the glove box, and puddle lights from tge wiring...

Removed the standard sidestep yesterday after a full cleandown. Looking at options for after fitted new batons/insulation/ply9mm/rubber floor. Anyone know why this says wont fit anything but a Caravelle? Not 100% on the differences...

Hi Having recently converted my interior roof mounted lights to LED lamps, I'm now looking to swap my front driver and passenger step lamps also to LED. These are the ones that have 4 separate warm white lamps currently installed. Does anyone know the lamp type so I can order some replacement...

So. I've got myself some step covers... but not sure what to use to attach them...? They don't appear to have any screw holes to screw them on... Double sided tape or some kind of adhesive gripper...?

Hi, can anybody help me out? Trying to find the step with the night heater vent and the courtesy light. Does anybody know of a part number or does someone have a reg I can give TPS for the part please. thanks in advance!