T6.1 camperglass flush windows problem

[Gerz]

Hi all. Installed camperglass Flush windows today on a T6.1 conversion. Used J trim. Prepped with primer on glass and panel. Felt like a got a decent height on the Adhesive using the v notch on the supplied nozzle. But front edge on both sides didn’t take like top bottom and back edges and felt squishy. Didn’t bond like rest and ended up with gaps. (See pics) has any one got any idea what could have caused this or a fix ? Or should I take windows out and start again from scratch. They look ok and sit nicely. But got concerns about squishyness and not being as solid as other 3 edges.

Cheers.

 

[mikeyb7]

Hi @Gerz sorry to dig up an old thread, did you ever solve this? I installed a driviers side flush sliding window this wkd and can see a couple of gaps to the bottom corner closest to the drivers door, I'm wondering if I can fill it with some sika ebt? Thanks!

 

[Gerz]

Hi @Gerz sorry to dig up an old thread, did you ever solve this? I installed a driviers side flush sliding window this wkd and can see a couple of gaps to the bottom corner closest to the drivers door, I'm wondering if I can fill it with some sika ebt? Thanks!

Hi ,

I bit the bullet and had them cut out and re done professionally. Cost £180 but money well spent, Guy who did it says he does loads. So probably a common occurence. I did contemplate buying a wire kit to cut it out myself but glad i didn't as the guy said some people do this and accidentially cut off the plastic drainage bits, so then windows are scrapped too! he used like a diamond inpregnated rope on a reel so a bigger diameter than the cheese wire they cut windscreens out with.

 

[mikeyb7]

Thanks for the prompt response, was really hoping you'd managed to salvage it yourself! Where about's are you based, who did you use to re-fit? Thanks!

 

[Gerz]

HI , Nottingham. This is the company i used, were spot on and came to my workplace and did it .

Midlands Vehicle Glass

Derby, Nottingham, Leicester and surrounding areas.

midlandsvehicleglass.co.uk

 

[mikeyb7]

Thanks!

 

[Smileysmile]

Hi ,

I bit the bullet and had them cut out and re done professionally. Cost £180 but money well spent, Guy who did it says he does loads. So probably a common occurence. I did contemplate buying a wire kit to cut it out myself but glad i didn't as the guy said some people do this and accidentially cut off the plastic drainage bits, so then windows are scrapped too! he used like a diamond inpregnated rope on a reel so a bigger diameter than the cheese wire they cut windscreens out with.

You had your windows removed? Were you anxious having them removed? The glass edges are so close to the bodywork. Then you have to remove the bond adhesive from the body. My flush window has to be replaced as I spotted a deep scratch the installer didn't notice and my van is only 2 years old. I'm nervous that they'll damage the surrounding paintwork.

 

[Gerz]

You had your windows removed? Were you anxious having them removed? The glass edges are so close to the bodywork. Then you have to remove the bond adhesive from the body. My flush window has to be replaced as I spotted a deep scratch the installer didn't notice and my van is only 2 years old. I'm nervous that they'll damage the surrounding paintwork.

Yes had them removed and redone, was a bit anxious, but trusted a pro over myself and the guy came highly recommened. Not that different to having a windscreen cut out.

 

[Smileysmile]

Yes had them removed and redone, was a bit anxious, but trusted a pro over myself and the guy came highly recommened. Not that different to having a windscreen cut out.

So I guess you had a go at diy. Then left it to the professionals which meant removing the side windows. I left it to the professionals, they installed them and they looked great. On inspection when I got home I noticed one had a one inch scratch which you could feel with your finger nail.
The other side has two marks, like finger tips which won't rub off. I think I'm going to have to live with that one. I was disappointed that they didn't fully inspect before installing.

They will replace the scratched window. I'm pretty nervous on the method of removing it without causing damage. I have been worrying about it. It's only a 2 year old van.

I've looked on YouTube. Removing with cheese wire. So close to the bodywork has traumatised me

 

[Gerz]

if you check back on this post I mentioned that the company used like a diamond inpregnated rope on a spool that slowy closed in , i'm so glad i didn't try to wire it off after knowing what method and specialist tools they used. And the main risk is cutting off the drainage bits. I accepted i'd messed up and to correct it , it was the best £180 i spent to make it right and cause me less stress.