A few more of the passenger area.
Hex Ply lining kit
- Thread starter Joe123
- Start date
Thanks for the photos, that looks really good! I think I'll get the sound deadening and insulation sorted out first, then pull the trigger on a set of these panels. I'm drawn to it as it looks nice (IMO), but it's also practical too.
What clips did you use to fasten the ply to the van? I'm assuming they utilise the facory holes?
What clips did you use to fasten the ply to the van? I'm assuming they utilise the facory holes?
That’s exactly why I went for them. I really like plywood and have furniture at home and in the back of the van with a coloured hardwearing final finish which has proven very hardwearing.
Factor in that I have a Fox Red Labrador, whose fur still CK’s to carpet very easily, and you can see why this stuff fits my needs perfectly.
They use the factory holes and I used the clips that the vendor supplied. 100 longer clips in black plastic for £20. I do have one whole that doesn’t line up with the corresponding hole in the van. It looks like it might be drilled slightly out, but I am not certain of that as it was the final clip to do. There’s a chance that a bit of adjustment might be potentially possible if I took all of the other clips out, but I don’t want to risk the integrity of the clips for the sake of the corner hole of one of the rear panels. It’s out of view so I will live with it I think. It’s not spoiled my opinion that’s for sure.
I now just need to consider what I do with the roof/ceiling panels. Any cool suggestions @CooseVW? What are you thinking of doing?
Factor in that I have a Fox Red Labrador, whose fur still CK’s to carpet very easily, and you can see why this stuff fits my needs perfectly.
They use the factory holes and I used the clips that the vendor supplied. 100 longer clips in black plastic for £20. I do have one whole that doesn’t line up with the corresponding hole in the van. It looks like it might be drilled slightly out, but I am not certain of that as it was the final clip to do. There’s a chance that a bit of adjustment might be potentially possible if I took all of the other clips out, but I don’t want to risk the integrity of the clips for the sake of the corner hole of one of the rear panels. It’s out of view so I will live with it I think. It’s not spoiled my opinion that’s for sure.
I now just need to consider what I do with the roof/ceiling panels. Any cool suggestions @CooseVW? What are you thinking of doing?
Last edited:
Hi what would be the cost of a hex floor for a LWB with the holes for mounting points cut out please and what thickness would it be?
Hi, here are the prices for the Hex floors. They are 15mm thick.
SWB 15mm HEX floor - £216
LWB 15mm HEX floor - £228
Packers supplied and fitted £35
Kombi cut outs £15 (per floor)
DRING cut outs £15 (per floor)
Delivery (Halos/Floors) to Residential Address £55
Thanks
SWB 15mm HEX floor - £216
LWB 15mm HEX floor - £228
Packers supplied and fitted £35
Kombi cut outs £15 (per floor)
DRING cut outs £15 (per floor)
Delivery (Halos/Floors) to Residential Address £55
Thanks
Hi, do you have a photo of the mis aligned hole so I can check the drawing? Not heard of this previously, but so easy to move a hole by accident on the drawing? How far out of line is it? Thanks
I will check it out when I get a chance, as I have not removed all of the other clips to see if I can realign it. I can’t get a clip through, so it appears to be out at least the width of a clip.
Easiest thing is to measure the distance to that hole to a number of other holes. If they match, then it might just be alignment, otherwise it’s in the wrong place.
Will let you know once I have checked it.
which hole is it? the one at the bottom behind wheel arch?
It’s the driver side panel nearest bottom left rear corner.
Hi you say it comes with packers, I’m assuming this is the bit that goes in the gaps and I just bind it to the floor, also then dodo mat in between?
It is. We bond our floors down so yours will have to either glue to ridges (without packers) or float with Packers on insulation
I’ve sent you an email to get some prices so hope to hear back from you soon thanks.
Thanks, I'll look out for it, what's your name?
Rob Nisbet
