CAN someone help me out. ABS control unit problem after accident

[Peterrr]

I have a T6.1 with damage to the left front. The ABS pump connector with the 38 pins had to be replaced. Now I don't know which wire goes on which pin. I have the following wires:
2x ground (both brown)
2x power (both red)
1x power contact (blue/black?)
1x power contact (red/green?)
Wheel sensor LF (1 brown and 1 black)
Wheel sensor LR (1 green and 1 black)
Wheel sensor RF (1 black and 1 brown)
Wheel sensor RR (1 black and 1 brown)
CAN L (orange/black?)
CAN H (white?)
I've looked at all the diagrams in the download section ( VIP member), but I can't find one with a CAN L that has an orange/black wire and a CAN H that has a white wire.
So the big question is, which pin should these wires go on?

 

[manfrotto]

Does this help?



It is from the wiring diagrams from 2016.
I couldn't see and white wires

 

[mmi]

I have a T6.1

This one below is for T6.1: However, it seems that there have been some updates since

ABS Wiring Diagram

28 Jan 2021

Current flow diagrams

• Pauly
• current flow diagram transporter t6.1 vw t6.1 wiring diagram
• VW T6.1 Electrical Info

E.g. wire colouring for the CANbus has been updated - pins they connect to are still the same

 

[Peterrr]

This one below is for T6.1: However, it seems that there have been some updates since

ABS Wiring Diagram

28 Jan 2021

Current flow diagrams

• Pauly
• current flow diagram transporter t6.1 vw t6.1 wiring diagram
• VW T6.1 Electrical Info

E.g. wire colouring for the CANbus has been updated - pins they connect to are still the same
View attachment 297711

where did you find this one? the one i downloaded has a orange/white wire

 

[F-roger]

I have a T6.1 with damage to the left front. The ABS pump connector with the 38 pins had to be replaced. Now I don't know which wire goes on which pin. I have the following wires:
2x ground (both red)
2x power (both brown)
1x power contact (blue/black?)
1x power contact (red/green?)
Wheel sensor LF (1 brown and 1 black)
Wheel sensor LR (1 green and 1 black)
Wheel sensor RF (1 black and 1 brown)
Wheel sensor RR (1 black and 1 brown)
CAN L (orange/black?)
CAN H (white?)
I've looked at all the diagrams in the download section ( VIP member), but I can't find one with a CAN L that has an orange/black wire and a CAN H that has a white wire.
So the big question is, which pin should these wires go on?

I've never seen a brown power supply and a red ground, you've got it mixed up.

 

[F-roger]

I think it will help.

 

[Peterrr]

I think it will help.

View attachment 297719

View attachment 297720

View attachment 297721

View attachment 297722

View attachment 297723

Yes you are right. i mixed them up writing it down. ground is brown and red is power. unfortunately your images are a little bit blurry. can you send me better ones?

 

[F-roger]

I don't know how to send you high-quality data from my phone, all the information is taken from a free resource.

https://superetka.com/elsa/?marke=V&modelljahr_numerisch=2022&vtyp=SHC&mkb=CXHA&gkb=PSS&dir=slp&dokument_id=5833711

 

[Peterrr]

I don't know how to send you high-quality data from my phone, all the information is taken from a free resource.

https://superetka.com/elsa/?marke=V&modelljahr_numerisch=2022&vtyp=SHC&mkb=CXHA&gkb=PSS&dir=slp&dokument_id=5833711

Thank you very much!!

 

[mmi]

where did you find this one? the one i downloaded has a orange/white wire

VW Online service information -

Volkswagen AG erWin Online

volkswagen.erwin-store.com

 

[Peterrr]

VW Online service information -

Volkswagen AG erWin Online

volkswagen.erwin-store.com

thanks!