Search results for query: centre bore

...into the wheel, has anybody come up with a solution to this? im thinking a small 3D printed reducer maybe pushed in from rear using the taper of the centre bore then clip the cap into that from the front? has anyone made anything? i havent got a 3D printer hence the question/suggestion...

The are the same wheel, just a different offset and centre bore. The face is the same

I was just about to post the same.. Apart from not being load rated, the centre bores are different sizes and the bolts have different seats. The OP got off lightly and has hopefully learned a thing or two.

...just on the inside as you'd expect, that will come out with elbow grease if you want them immaculate. Outside faces all spotless. All tyres have around 7mm to 8mm across all treads. Tyre size 205/65R16C 107/105T Wheel size 16" PCD 5x120 Centre Bore 65.1mm £350 Collection only from Exeter.

Cheers lads, I couldn't find or see the centre bore size anywhere.

...with the secs below. My question is I don't want the wheels to poke out beyond the wheel arch's. Can anyone advise on the specs below. Cheers Size: 20 Inch Width: 8.5J & 10J Offset (ET): +35/+40 Respectively PCD: 5x120 Centre Bore: 72.6mm (Spigots Included) Max Load (per wheel): 885kg/1950lbs

...at the painters. Result is the paint is thicker than it should be, but at least they shouldn’t rust quickly… The issue is with the centre bore. Tight. You can see where I’m going with this! I used wheel bolts to pull wheel onto centre bore thinking it would push out excessive paint. It did...

With the canteras is the centre bore the same or do you need spigot rings?

20” 8.5J & 10J Offset: +35mm & +38mm Concave: 40mm & 60mm PCD: 120 Centre Bore: 72.6mm (72.6-65.1 spigots attached) Max Load (per wheel): 875kg Come with 275/35/20 and 245/40/20 budget tyres that have a few miles left Also comes with wheels nuts including lockers A bit of kerbing damage and...

...120 72.6CB Load Rated to 850kg Velare VLR08 Size: 20 Inch Width: 8.5J & 10J Offset ET: +35mm & +38mm Concave: 40mm & 60mm PCD: 5x120 Centre Bore: 72.6mm (72.6 - 65.1 spigots included) Max Load (per wheel): 875Kg These look pretty similar to me - anyone got experience of either...

Hi Thanks for that, I've got lots of clogging DPF issues. I really need to get in touch with someone who takes these engines apart and fixes them. VW Van Centre are talking about whole engine replacement, 13k +. I'm sure there must be a better way.

We’ve went the other way, booked all the sites and figuring out what we are doing between them. Starting in Aviemore and ending in Glencoe though. Our 6yo will be bored stiff if she doesn’t get Landmark Park and the Highland Wildlife Centre at the start.

Thanks for your message Dave. I spoke to Rimstyle and they are supplied with spigot rings so all good. Thanks for your advice

Straight swap, didnt use spigot rings on mine

Lowering the price has created a lot of interest... Please check the dimensions fit your vehicle, as I do not want them returned if they don't fit... Especially centre bore. These wheels = 65.1mm, occasionally some vans have bigger hubs. Load rating is 930kg per wheel.

...bottom of the threaded holes and let them rattle around. The spigot rings centre the wheels on the hubs when the hub is smaller than the centre bore of the wheel, this should take most of the weight of the vehicle, the bolts just hold the wheel onto the hub once its supported by the spigot...

Hi I’ve just got these new wheels Size: 20 Inch Width: 8.5J & 10J Offset (ET): +35/+40 Respectively PCD: 5x120 Centre Bore: 72.6mm (Spigots Included) Max Load (per wheel): 885kg/1950lbs And I really need to know what tyres to put on them it’s a t28 with standard suspension at the mo and help...

You could pop a 5mm shim behind the wheel to aid clearance. The recent Revenge centre bore is same as VW so that rules out a hub centric spacer of 10mm, so try a 5mm shim. Is the van a T32? I’m assuming yes and that’s why you chose that tyre size. Are you sure it’s a 70mm drop? Has that been...

...set of Velare VLR08 diamond black alloys, in fantastic condition. Spec as follows… 20 x 8.5” ET35 Front, 20 x 10” ET38 Rear 5x120 PCD, Centre Bore 72.6mm (72.6 - 65.1 spigots included to fit Transporters) Brand new set of 20x black 35mm bolts also included. Load rated to 875kg so suitable...