Search results for query: CXEB

Hi advice need a company rebuilt my engine for me to refit got all back together hard to fire up but it running got crank shaft sensor fault there is power there so bought new sensor same fualt also spotted new oil on the senor when I removed it so seal is leaking the rebuild company has agreed...

Evening all I was doing an engine oil and fluid check today, and remember some on here suggesting that a blocked / dead PCV would likely be causing a proportion of the engine oil consumption. So i googled it, googles AI thing suggested I remove the engine oil cap with the engine at idle, stand...

So I’ve recently acquired a 2017 CXEB engined T6 with a blown turbo and wet exhaust manifold ports (all 4) so I’ve pulled the engine and it’s gone to an engineering firm who are going to pull it apart this / next week and let me know the outcome but assuming it’ll have a full refresh. I’m going...

...looking for recommendations for garages within reasonable reach of Oxford who can do specialist diesel/turbo diagnostics for my 2017 T6 204bhp CXEB T32 DSG 4wd transporter. Broke down last week with loss of power, orange coil light flashing, black smoke out of exhaust on hot motorway journey...

Hi Everyone ,this is the first time i have posted . Can anyone advise that i have the correct software running ,currently 04L907605KN/3776. I believe there may be an emisiions update in 2019 affecting the final 4 digits "3776". All advice gratefully received . Thanks in advance Paul

Hi everyone, I’m looking for some help and real-world experience from members who have dealt with CXEB 2.0 BiTDI engines, especially regarding engine rebuilds and oil consumption issues. Vehicle details: Engine: CXEB 2.0 BiTDI Year: 2016 Mileage: 181,000 km Oil consumption: ~1L / 1,000 km Aside...

Hi all, I know this is a very popular subject on here but hoping to get some advice from those who have been through this. So last week while on the motorway the van started whistling and making a noise on acceleration, finally there was a pop, the Glow Plug light came on, start/stop issue and...

Hi all, our Easter trip in our T6 (2018 plate, 204 CXEB on about 69k miles) got off to a bad start with a flashing coil light and what I assume was limp mode, just after arriving on the ferry from Hull to Rotterdam. For context, we had just completed an 80 minute drive from York to Hull and as...

Just replaced intake manifold (genuine) due to swirl flaps stuck. After putting it all back together and running it down the road it seemed fine. Set off up hill and went flat out and the glow plug light started flashing and vehicle went into limp mode, recycled the ignition and full power...

Greetings fellow T6 enthusiast! I am one of the unlucky champs with a CXEB that uses way too much oil than it should. This in turn has led to turbo-failure and prompted me to replace them and whilst at it to prevent further issues, delete EGR and DPF. Stumbled across another T6-owner that webt...

is there anybody with a CXEB and OBDeleven that could check what the wastegates actuatorvoltage is set to when ignition is off? I’m having trouble adapting the new turbo on my T6 and the workshop manual states that I should set a vacuum at 0,5 bar on the actuator and adjust the arm so the...

I've been ringing around for prices on a compression test on my 2018 CXEB and the prices are varying wildly. My local specialist wants £300 and VW commercial ranges from £174-500. The cheapest VW van centre, £174, said it'll only take them an hour but if it was a VW warranty job (it is not)...

As per title, I'm looking for an engine oil flow diagram to Ian in the installation of a front mounted oil cooler for my CXEB powered T6 I've finally found an oil take off plate that fits in place of my OEM liquid to liquid oil cooler, there are two outlet bosses, but they are un-marked, I need...

As per title… Is it possible to fit a FMIC to a CXEB engine? This would involve the removal of the engine mounted charge cooler, front mounted charge cooler radiator, associated pipework and water pump? If it is possible (I’m sure it is) how much of a benefit would there be in terms of power...

...too much oil is the block wearing and its just about what VW would call ‘normal’ Or do I pull the turbos? Is there something i’m missing? I expected to find something obvious. I might borescope the cylinders before it goes back together. But if all good, then what? 🤔 CXEB 204 MY19 LWB 4MOTION

Hi all, I’m new to the forum and hoping someone can point me in the right direction. I’ve recently bought a 2016 T6 with the CXEB engine, and I’m struggling with an issue I can’t seem to pin down. Symptoms: With all fault codes cleared, the van will start from cold and just about idle for...

...the discussions I could find on this forum and others and can not seem to resolve my issue. I recently replaced my intake manifold. And for the CXEB engine that means usually the front needs to come of. To get to the bolt behind the fuel pump I used a custom wrench but needed to remove the...

Hello... i'm gonna overhaul my cxeb engine and need a workshop manual for all the bolt tourqe and boresizes and bearing clearances etc.. I can not seem to download the file under the downloads tab... Can I find the manual somewhere? (if its free would be great, on a tight budget :( ) Best...

Hi all, I've searched the forums and google but can't seem to find a solution.... Wanting to do a compression test on my CXEB and understand I'll need a long reach M10x1 fitting but I cannot find anything.... A few people have posted about needing one for this job, but I can't find any posts of...

Is there any info to be found regarding what stock charge pressure should be on a T6 with CXEB engine?