Search results for query: grommet

...issues? With respect to getting the cable through the bulkhead, is it just a case of removing the glovebox and the battery and then feeding the cabling through a grommet which is already in place? Apologies if I am way off the mark, but I have not removed any of the cab or dash sections so far.

All went good. I managed to squeeze the cable through one of the grommets passenger side that comes out behind the battery. It was a squeeze. Another way would be to drop the black neg cable and just put the +ve red through one of the grommets to the battery. The black neg can then be put...

How did you get on in the end, I am about to do the same but I already have cables in the passenger side grommet

Ensure the hole in the van floor has a smooth edge, preferably a heat resistant grommet. I’ve worked on two vans where the underslung heater hose has been cut by a sharp floor edge, I can’t imagine anybody thinking it was going to end well done like that, probably a converter churning out high...

A bit of progress yesterday afternoon. Stripped out the front cab for easy access to factory loom routes and to the grommets behind dash.

...and internal and external access flushed through, external pipe well and truly squeezed, coolant system pressure tested ok, scuttle plate and grommets cleaned out. Lower dash completely stripped off, evidence of drips behind fuse box and from box which is part of aircon pipe system (have...

Most people put the hook up socket under the bonnet and feed the cable in through one of the grommets that lead into either of the footwells. Lots of info on here.

...for you? I have a T6.1 2023 Beach and will fit a small integrated subwoofer from Pioneer that I will fit with a sock harness from Absolut5 and am wondering how people have routed the wires from the dash to under the seat? have you used the grommets and channeled outside or just under the carpets?

...had much interest but would like these to be used by someone. So I've dropped the price and am open to offers, I've also started to make the grommets to plug the top holes, in case that may have been putting people off, So I can do them like the photo and supply extra rubber for you. Cheers...

...hole inserts for the top of the rails. But I will endeavor to make some if you wish, out of rubber. Or you can buy off ebay rubber blanking grommets. The instructions mention double sided rubber tape/patches. I can supply these. They also mention rubber sealant, but I'd imagine silicon or...

Had similar issue & posted about it too previously. They don't fit well at all. Mines just barely hanging onto the rubber grommets when it is sitting correctly at the front. If I push it fully onto the rubber grommets then it doesn't reach the popper on the front...

Do you need to remove wipers to remove plastic trim to remove the black cover that is mounted right there in the pic or can that panel be removed without taking the plastic off?

Thanks for the reply. Yeah I think the plan is now to put the battery just in front the wheel arch by the kitchen unit. I have a tailgate, but was going to run the solar cables through the existing grommit. My only issue is I feel like I'm not making great use of the space under the drivers...

...the battery and the inverter - it can be done but they are going to be large to cope with voltage drop. You'd be better off putting them together in the rear, in fact I'd put the MPPT there too especially if you have barn doors and use the tailgate hinges grommet to route the solar panel...

I went in through the sill with the waste and feed pipes, the grommet is quite big. Needed two of us, one feeding up from below, me trying to fish it out of the cill from the inside. https://www.t6forum.com/threads/candyvan-conversion-journey.37860/post-536317

Hallo mate have you got any more pics of this as this is what I’m looking at doing this weekend but a 20mm waste won’t fit those holes? Did you drill them to make them bigger or am I missing something? Thanks!

If you have barn doors then a popular route is to use the blanked off mounting points for the tailgate hinges - should just have grommets in them. Its not the SOS module itself, it's the primary LTE antenna, but don't mess with it all sorts of fault codes lie in your future if you do that ;)...

Nice to hear. Thank you for trusting me. The device really has no protection from moisture, if I seal it hermetically, then we will not be able to update the software. I periodically release firmware updates in which I eliminate minor inaccuracies that occur when working on different cars, as...

...the dark blue plugs at the bottom of the holder (position 10) so that was annoying lol. I would also recommend getting the flattop fuse box grommet to run it properly into the front of the fusebox. Vans now gone off to have the ADAS position checked, then the rest of the front can be put...

Sounds like a plan. Where do you guys have your EHU sockets and would you have them there if you did it all over again? Really only need 1x double Id say