VW T6.1 Problem with ABS coding??

[bratchd16]

Good evening,
I have a VW T6 in the garage at the moment that had an ecu kit fitted (2nd hand) but during this process, after fitting cluster and head unit noticed the ecu was different so all original components were fitted. Now van has an arrangement of lights on the dash and during scan with ODIS found that long coding is zeroed out.
Would anyone have a coding that could be written back in to get the ABS pump up and running again?

I have attached a few images, thanks for any help in advance.

REG= G9CSD

 

[Pauly]

If you have ODIS can you not SVM it to restore factory config ?

 

[Robert]

You can restore your ABS coding manually.
All you need are your VIN and your equipment setup( wheelbase size, brake size, ACC/Front Assist, HDC, TPMS and so on).

 

[bratchd16]

Thanks for the replies, im pretty new to ODIS to be honest and didnt want to cause any further issues, how would i go about both of these scenarios?

 

[Robert]

Have a look below and try your best guess.

Want ESP/TC Button in my 2017 Caddy, abs mk100 coding?

Hello, I have retrofitted an ESP / TC Control button in my 2017 vw Caddy. highline 150/6speed. Wired it up to abs unit as the wiring scheme says. but nothing happens, I have now searched the net for info about ABS mk100 coding, but cannot find anything.. Anyone here who can help me? Thanx...

forums.ross-tech.com

After that you will see in the fault codes things you have missed.

 

[bratchd16]

I will have a look through that just now and update you guys tomorrow.
Thanks for taking the time to reply

 

[Pauly]

If your ODIS is genuine and licensed then there is an SVM (software version management) option that will connect to the VW mothership and download/restore everything back to factory configuration

 

[bratchd16]

The ODIS we are using is not genuine i believe, one of the guys that work here brought it in to try as the diagnostic software we have wasent doing much in way of coding. I have OBD eleven coming today with the ultimate pack so hopefully be able to try coding ABS via that

 

[mmi]

Based on ABS part number it's actually a T6.1. The ABS controller is made by Bosch, whereas T6 controller is made by Continental. Thus the referenced MK100 controller documentation doesn't help much as such.

I'm afraid that OBDeleven doesn't provide any help for the coding.

Have you checked log/scan files of the ODIS - for the coding?

Most likely the only way is to pay visit a VW dealer and have them to restore the original coding.

 

[Robert]

Have a look below and try your best guess.

Want ESP/TC Button in my 2017 Caddy, abs mk100 coding?

Hello, I have retrofitted an ESP / TC Control button in my 2017 vw Caddy. highline 150/6speed. Wired it up to abs unit as the wiring scheme says. but nothing happens, I have now searched the net for info about ABS mk100 coding, but cannot find anything.. Anyone here who can help me? Thanx...

forums.ross-tech.com

After that you will see in the fault codes things you have missed.

Sorry, I was convinced the question was about T6.
By the way, I got the thread title corrected.

 

[bratchd16]

Sorry about that,
The ODIS I have allows me to extract all the info for coding then asks for online login....can this be purchased somewhere like a pass through system?

 

[Robert]

Sorry about that,
The ODIS I have allows me to extract all the info for coding then asks for online login....can this be purchased somewhere like a pass through system?

Yes, look up "odis account" on Aliexpress.
But bear in mind that only some of the clone VAS interfaces are actually allowed to fully log in.

 

[Craig.]

Sorry about that,
The ODIS I have allows me to extract all the info for coding then asks for online login....can this be purchased somewhere like a pass through system?

Where are you based?

ODIS will allow you to specifically target the ABS module for online coding, adaption and calibration.

 

[bratchd16]

Where are you based?

ODIS will allow you to specifically target the ABS module for online coding, adaption and calibration.

Hi. Thanks for your replies.
I'm based in Glasgow and desperate to get the van back on the road as it seems to have a list of faults since this has happened.

 

[Craig.]

Hi. Thanks for your replies.
I'm based in Glasgow and desperate to get the van back on the road as it seems to have a list of faults since this has happened.

AAAhhhh damn, I'm a solid 400 miles away so I'm no help, I'll check if I know any independent specialists in the area with ODIS that can help and get back to you.

 

[bratchd16]

AAAhhhh damn, I'm a solid 400 miles away so I'm no help, I'll check if I know any independent specialists in the area with ODIS that can help and get back to you.

Thanks that would be a great help, I really appreciate all the help and comments