OEM Webasto Auxiliary Heater To Parking Heater Upgrade

[Robert]

Generally speaking you can not have two control modules with the same address on the CAN bus of the same vehicle. There would be constant conflict for both, internal communications and also for diagnostic purposes.

I will be facing exactly same issue when will have to sacrifice Highline Reversing Camera module (6C) and throw it away to be replaced by Area View 2 module (6C).

So another words you have to prioritise and select only one and the most useful control module for your maximum benefit and convenience.

 

[Herrades]

Okay, sounds understandable.

but once i understand. How know the panel which heater is controllable?
If you have the water aux. heater installed stock, you can set „only fan“ in the overhead panel to bring fresh air in the car.

This function is not available when you have the air heater from factory inside.

anywhere must the panels be different, otherwise you can set the air heater only to set only fan too.

Or read it via can which one is installed?

i dont know.. as i said, i try a water aux. hater panel and check the different in the Car

maybe i can flash my H panel into a J panel? Also this i would like to test. But not with mine, for the test i take the second once

 

[Herrades]

Okay, 6 hours later and the remote control t91r works very fine. Configure the water aux. heater in vcds to only remote control without overhead panel and it´s done.

Next step is the overhead panel but the delivery service are very slow and i must wait for my panel

Thats all for the very nice informations!!

The shit was to bring a cable from the heater to the t91r in the a pillar..

I´m very happy

Thx all!

 

[1Pearman]

Has anybody with Climatronic upgraded the Aux heater to a parking heater with the Danhag kit? Seems this requires no coding or re-flashing, and is plug and play via the red connector under the passenger seat. It also connects to a Webasto controller of your choice. Seems very simple. The info i'm struggling to find is if it's really 'usable' as a night heater, or only really as a 'defrosting' tool. The heater, coolant pump, fans etc will all be running from the starter battery which is no use for overnight usage. I guess the heater could be switched over to take 12v+ from the leisure battery, but that still leave the fans and pump. I'm also unsure if this kit allows the canbus to continue to operate the heater as an Aux heater for cold starts? I assume it does.

 

[C4S]

During the past few weeks of cold weather I have noticed a whirring underneath the van. My door has sticker indicating Thermo top Evo 5 KW

am I right in thinking the kit to make this act as a night heater is £160 ?

presumably it is difficult to fit and and re code ?

does any one on here fit this kit and do the re coding as opposed to taking it somewhere to be done at an extortionate cost ?

 

[Herrades]

Yes, you're both right.

The danhag tool would be connected via can. Danhag use the "service start for aux heater" modus to start the heater over can. You don't need to flash the heater and you must not coding everything. The tool do that every time ago and you can still use your heater all night long.
But watch out, when the battery are down, your car would't start. The aux. heater use power from the starter battery.

You just need the danhag Zuheizeraufrüstung VW T6 - Climatronic kit for climatic / climatronic.
But you are shure it will only cost £160 ?? In Germany they demands a lot of money. Here it cost 389€

 

[huw169]

Hi all

I'm currently toying with converting my webasto, or fitting a diesel heater.
Can the webasto aux heater be powered off a liesure battery, or does it screw up the can bus comms?

I'm not so concerned with engine warming, but more about van cab warming for de-icing and getting driving quicker, and over night heating on the occasional sleep night.
As for cost, webasto mod is about £200 from what I can see (DIY), but a 2kw chinese diesel heater is £80 but a bunch of my time to fit. Both will need liesure battery and split charge.
Currently sitting on the fence. I don't have the overhead control panel, so just trying to determine what would be the best route for my end goal.

Any insights guys?
Thanks

 

[1Pearman]

Hi all

I'm currently toying with converting my webasto, or fitting a diesel heater.
Can the webasto aux heater be powered off a liesure battery, or does it screw up the can bus comms?

I'm not so concerned with engine warming, but more about van cab warming for de-icing and getting driving quicker, and over night heating on the occasional sleep night.
As for cost, webasto mod is about £200 from what I can see (DIY), but a 2kw chinese diesel heater is £80 but a bunch of my time to fit. Both will need liesure battery and split charge.
Currently sitting on the fence. I don't have the overhead control panel, so just trying to determine what would be the best route for my end goal.

Any insights guys?
Thanks

The main issue I found was the battery. The Aux heater also needs a water pump and fan blowers to be working to heat the inside of the van. It’s essentially got to heat the engine coolant, pump it around and in doing so heat up the air blowing across the heat exchanger. That’s a lot of stuff running off the starter battery and whilst it’s pretty easy to rewire the heater to run from the leisure battery I think the other stuff just becomes a non starter. I’ll be going for a 2kw heater under the drivers seat.

 

[huw169]

The main issue I found was the battery. The Aux heater also needs a water pump and fan blowers to be working to heat the inside of the van. It’s essentially got to heat the engine coolant, pump it around and in doing so heat up the air blowing across the heat exchanger. That’s a lot of stuff running off the starter battery and whilst it’s pretty easy to rewire the heater to run from the leisure battery I think the other stuff just becomes a non starter. I’ll be going for a 2kw heater under the drivers seat.

Thanks for that @1Pearman
I was trying to figure out all the other stuff that would need to be running to achieve my end goal. I am definitely leaning towards the 2kw heater as it is self contained. I’m also not that fussed on warming the engine.

 

[mmi]

Thanks for that @1Pearman
I was trying to figure out all the other stuff that would need to be running to achieve my end goal. I am definitely leaning towards the 2kw heater as it is self contained. I’m also not that fussed on warming the engine.

The OEM Webasto + coolant pumps + cabin fan blower draw approx. 12 Amps when running.

 

[Florist]

Did anyone of you got the heater running with firmware 7E0 963 272 B and a Thermo Call TC3 or TC4? VCDS Coding is 4101, but same with 4001, 5101, 5001.
When I send the start command via sms, I can hear the heater making some sound for 1-2 seconds, but then it stops
Do I have to use the Webasto-flash software with blue dongle to get it going with the TC3 or TC4?
Thanks in advance and sorry for my bad english.

 

[mmi]

Did anyone of you got the heater running with firmware 7E0 963 272 B and a Thermo Call TC3 or TC4? VCDS Coding is 4101, but same with 4001, 5101, 5001.
When I send the start command via sms, I can hear the heater making some sound for 1-2 seconds, but then it stops
Do I have to use the Webasto-flash software with blue dongle to get it going with the TC3 or TC4?
Thanks in advance and sorry for my bad english.

VCDS Auto-Scan and wiring diagram/pictures would be helpful.

 

[Florist]

VCDS Auto-Scan and wiring diagram/pictures would be helpful.

Hi MMI,

thanks for your feedback!

Here's a picture of what's going on underneath my drivers seat



The wiring is as follows:

Webasto Thermo Call TC3:



- Pin 1 - +12V: Connected to +12V directly to the second battery
- Pin 2 - GND: Connected to the Ground bolt under drivers seat
- Pin 6 - W-Bus: Connected to the Green/White cable of the Red Connector

The Thermo Call receives sms messages and also sends messages back to my phone, but the heater doesn't start - only 1-2 second sound and nothing more.




Here's the VCDS Scan (sorry only in german) - It's a Gen 6 Multivan 10/2016 Model 2017:

Fahrzeug-Ident.-Nr.: WV2ZZZ7HZHH012345 KFZ-Kennzeichen:
Kilometerstand: 68360km Reparaturauftrag:


Fahrzeugtyp: 7H-VN75 (7E0)
Scan: 01 02 03 04 08 09 10 13 14 15 17 18 19 20 25 3C 55 5F 61 6D
0B

Fahrzeug-Ident.-Nr.: WV2ZZZ7HZHH012345 Kilometerstand: 68360km

01-Motorelektronik -- Status: i.O. 0000
02-Getriebe -- Status: i.O. 0000
03-Bremsenelektronik -- Status: i.O. 0000
04-Lenkwinkelsensor -- Status: i.O. 0000
08-Klima-/Heizungsel. -- Status: i.O. 0000
09-Zentralelektrik -- Status: i.O. 0000
10-Einparkhilfe 2 -- Status: i.O. 0000
13-Distanzregelung -- Status: i.O. 0000
14-Radd‰mpfung -- Status: i.O. 0000
15-Airbag -- Status: i.O. 0000
17-Schalttafeleinsatz -- Status: i.O. 0000
18-Standheizung -- Status: Fehler 0010
19-Diagnoseinterface -- Status: i.O. 0000
20-Fernlichtassistent -- Status: i.O. 0000
25-Wegfahrsperre -- Status: i.O. 0000
3C-Spurwechsel -- Status: i.O. 0000
55-Leuchtweitenreg. -- Status: i.O. 0000
5F-Informationselek. I -- Status: i.O. 0000
61-Batterieregelung -- Status: i.O. 0000
6D-Heckklappe -- Status: i.O. 0000

-------------------------------------------------------------------------------
Adresse 01: Motorelektronik (J623-CXEB) Labeldatei:. DRV\04L-907-309-V2.clb
Teilenummer SW: 04L 906 056 AE HW: 04L 907 445 A
Bauteil: R4 2.0l BTD H03 6206
Revision: 23101001
Codierung: 0025401C436401080000
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_ECM20BTD03004L906056AE 004007
ROD: EV_ECM20BTD03004L906056AE.rod
VCID: 706F205921C8FE40A7-8024

Kein(e) Fehlercode(s) gefunden.
Readiness: Nicht Verf¸gbar

-------------------------------------------------------------------------------
Adresse 02: Getriebe (J743) Labeldatei: DRV\0BH-927-711.clb
Teilenummer SW: 0BT 300 046 J HW: 0BH 927 711 G
Bauteil: DSG DQ500-7F H11 5302
Revision: 00H11V01
Codierung: 0014
Betriebsnr.: WSC 00000 000 00000
ASAM Datensatz: EV_TCMDQ500021 001001
ROD: EV_TCMDQ500021.rod
VCID: 3D308AA075CB00ED3F-8068

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 03: Bremsenelektronik (J104) Labeldatei: DRV\7E0-907-37x-MK100ESC.clb
Teilenummer SW: 7E0 907 379 Q HW: 7E0 907 379 N
Bauteil: ESC H06 0133
Revision: 00000000 Seriennummer: 42416000001018
Codierung: 307E4098656784840C7C0277A68221D378F700
Betriebsnr.: WSC 02739 790 50316
ASAM Datensatz: EV_Brake1ESCCONTIVN75XGP2 011001
ROD: EV_Brake1ESCCONTIVN75XGP2_011.rod
VCID: 403F80A961D81EF027-8014

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 04: Lenkwinkelsensor (G085) Labeldatei:* DRV\6R0-959-654.clb
Teilenummer SW: 6R0 959 654 HW: 6R0 959 654
Bauteil: LENKW.SENSOR H07 0070
Seriennummer: 10091613470902
Codierung: 01
Betriebsnr.: WSC 00000 000 00000
ASAM Datensatz: EV_LWSKLOVW25X 005001
ROD: EV_LWSKLOVW25X.rod
VCID: 7E710C63698E8A2237-802A

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 08: Klima-/Heizungsel. (J255) Labeldatei:| DRV\7E5-907-040.clb
Teilenummer SW: 7E0 907 040 R HW: 7E0 907 040 R
Bauteil: ClimatronicT5 H04 0510
Revision: 00001K04
Codierung: 0000000103
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_ClimatronicT5 A01003
ROD: EV_ClimaAutoT5Basis.rod
VCID: 322DA49F5912421E57-8066

Slave 1:
Subsystem 1 - Teilenummer SW: 7E5 907 049 C HW: 7E5 907 049 C
Bauteil: Heckbedienung H11 0303
Seriennummer: BHB-0011909160015002

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 09: Zentralelektrik (J519) Labeldatei:. DRV\7E0-937-BCM-V1.clb
Teilenummer SW: 7E0 937 090 B HW: 7E0 937 090
Bauteil: BCM PQ25 Max4 H81 0744
Revision: B9081001 Seriennummer: 0982 259161571
Codierung: 62D9793A0A21200201280F606CEB8FD4C094738960CD79603204003F0860
Betriebsnr.: WSC 02737 022 196550
VCID: 2A25B467312A925697-807E

Subsystem 1 - Teilenummer: 5K7 955 559 C Labeldatei: DRV\5K7-955-559.CLB
Bauteil: RLS 300816 04 42 0106
Codierung: 0228EE

Subsystem 2 - Teilenummer SW: 7E0 959 801 N HW: 7E0 959 801 N Labeldatei: DRV\7E0-959-80X-V2.CLB
Bauteil: J386__TSG_FT 003 0654
Seriennummer: KU0KU008091662520570
Codierung: 0400A1

Subsystem 3 - Teilenummer SW: 7E0 959 802 N HW: 7E0 959 802 N Labeldatei: DRV\7E0-959-80X-V2.CLB
Bauteil: J387__TSG_BT 003 0654
Seriennummer: KU0KU007091662518890
Codierung: 1400A1

Subsystem 4 - Teilenummer SW: 7E0 959 442 A HW: 7E0 959 442 A Labeldatei: DRV\3C8-959-537.CLB
Bauteil: E221__MFL-DC1 H02 0103
Seriennummer: 29160001680820116347
Codierung: B4FFFF

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 10: Einparkhilfe 2 (J446) Labeldatei:| DRV\7E0-919-475.clb
Teilenummer SW: 7E0 919 475 AA HW: 7N0 919 475
Bauteil: PARKHILFE 8K H06 0212
Revision: -------- Seriennummer: 28231622501505
Codierung: 308909
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_VW75XParkAssis8K 001012
ROD: EV_VW75XParkAssis8K_001_VN75.rod
VCID: 716C225C25CFF8595F-8024

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 13: Distanzregelung (J428) Labeldatei:| DRV\7N0-907-572.clb
Teilenummer SW: 7N0 907 572 C HW: 7E0 907 572
Bauteil: ACC Bosch PQx H03 0210
Seriennummer: 19081604380299
Codierung: 00005000FE0779
Betriebsnr.: WSC 01383 790 50316
ASAM Datensatz: EV_ACCBEGVW361 001006
ROD: EV_ACCBEGVW361_VW32.rod
VCID: 36299C8B49E65A3A77-8062

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 14: Radd‰mpfung (J250) Labeldatei:. DRV\3C0-907-376.clb
Teilenummer SW: 3C0 907 376 A HW: 3C0 907 376
Bauteil: DAEMPFUNGS-SG H07 0071
Revision: 00000000 Seriennummer: 15051606760002
Codierung: 000180
Betriebsnr.: WSC 02759 790 00000
VCID: 2726BE7E055D8443EF-8072

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 15: Airbag (J234) Labeldatei:| DRV\5K0-959-655.clb
Teilenummer SW: 7E0 959 655 H HW: 7E0 959 655 H
Bauteil: VW10Airbag01V H08 0018
Revision: -------- Seriennummer: 003V40017TJ8
Codierung: 000000000000000000000000000000003156
Betriebsnr.: WSC 02734 790 50316
ASAM Datensatz: EV_AirbaVW10BPAVW12X 001028
ROD: EV_AirbaVW10BPAVN750_VW12.rod
VCID: 3B3296BA7DC13CDF0F-806E

Crashsensor f¸r Seitenairbag Fahrerseite:
Seriennummer: 3495ZRB401G579DAE1NP

Crashsensor f¸r Seitenairbag Beifahrerseite:
Seriennummer: 3505ZRB401G579DAAP8M

Crashsensor f¸r Seitenairbag hinten Fahrerseite:
Seriennummer: 3515ZRB401A579DAPHBR

Crashsensor f¸r Seitenairbag hinten Beifahrerseite:
Seriennummer: 3525ZRB401C579DAJHGT

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 17: Schalttafeleinsatz (J285) Labeldatei:| DRV\5K0-920-xxx-17.clb-SRI1
Teilenummer SW: 7E0 920 880 S HW: 7E0 920 880 S
Bauteil: KOMBI H04 1105
Seriennummer: 00000000000000
Codierung: 140F010400
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_Kombi_UDS_VDD_RM09 A05733
ROD: EV_Kombi_UDS_VDD_RM09_005_VW25.rod
VCID: 3A3594B779FA32C617-806E

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 18: Standheizung (J364) Labeldatei:| DRV\7E0-963-27X-18.clb
Teilenummer SW: 7E0 963 272 B HW: 7E0 963 273
Bauteil: STH-T5GP2 002 0009
Codierung: 4001
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_AuxilParkiHeateWOST5G2 001013
ROD: EV_AuxilParkiHeateWOST5G2.rod
VCID: 2B22B66A3D319C6F8F-807E

1 Fehler gefunden:
0266 - Datenbus fehlende Botschaft
U1121 00 [009] - -
[TIMEOUT mDachdisplay]
best‰tigt - gepr¸ft seit letzter Lˆschung
Umgebungsbedingungen:
Fehlerstatus: 00000001
Fehlerpriorit‰t: 6
Fehlerh‰ufigkeit: 1
Verlernz‰hler: 98
Kilometerstand: 68361 km
Datum: 2021.04.27
Zeit: 03:39:45

Standheizung: Betriebszustand: aus
71
K¸hlmitteltemperatur der Standheizung: 12 ∞C
K¸hlmitteltemperatur: 10 ∞C
Status Motorlauf: nicht erkannt
Kraftstoffvorrat: 80 l
Heizleistung: 0 W


-------------------------------------------------------------------------------
Adresse 19: Diagnoseinterface (J533) Labeldatei:. DRV\7E0-909-901.clb
Teilenummer SW: 7E0 909 901 HW: 7E0 937 090
Bauteil: GW-K-CAN TP20 H81 0744
Revision: B9081001
Codierung: 04220F
Betriebsnr.: WSC 02737 022 196550
VCID: 6867302109E00E98E7-803C

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 20: Fernlichtassistent (J844) Labeldatei:| DRV\8S0-857-511.clb
Teilenummer SW: 7E0 857 511 F HW: 7E0 857 511 C
Bauteil: FLA H10 0003
Revision: AA001001
Codierung: 040400E200000000000000
Betriebsnr.: WSC 02739 790 50316
ASAM Datensatz: EV_HighBeamAssisAU316 001004
ROD: EV_HighBeamAssisAU316.rod
VCID: 2D20AA90353B607DBF-8078

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 25: Wegfahrsperre (J334) Labeldatei:| DRV\5K0-920-xxx-25.clb
Teilenummer SW: 5K0 953 234 HW: 5K0 953 234
Bauteil: IMMO H04 1105
Seriennummer:
Codierung: 000000
Betriebsnr.: WSC 00000 000 00000
ASAM Datensatz: EV_Immo_UDS_VDD_RM09 A03710
ROD: EV_Immo_UDS_VDD_RM09.rod
VCID: 6A65342739EA129697-803E

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 3C: Spurwechsel (J769) Labeldatei:| DRV\5Q0-907-566.clb
Teilenummer SW: 7E0 907 566 C HW: 4H0 907 566 F
Bauteil: SWA Master H08 0030
Seriennummer: 0414559094
Codierung: 030311
Betriebsnr.: WSC 02739 790 50316
ASAM Datensatz: EV_LaneChangAssis 001028
ROD: EV_LaneChangAssis_VN75.rod
VCID: 302FA09921087E00A7-8064

Steuerger‰t 2 f¸r Spurwechselassistent:
Subsystem 1 - Teilenummer SW: 7E0 907 568 C HW: 4H0 907 568 F
Bauteil: SWA Slave H08 0030
Seriennummer: 0414529552
Codierung: 030311

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 55: Leuchtweitenreg. (J431) Labeldatei:. DRV\6R0-907-357.clb
Teilenummer SW: 6R0 907 357 C HW: 6R0 907 357 B
Bauteil: AFS-ECU 005 0050
Revision: -------- Seriennummer: --------------
Codierung: 0FC2020001000000
Betriebsnr.: WSC 02757 790 50316
ASAM Datensatz: EV_HeadlRegulVWLWRCC 002006
ROD: EV_HeadlRegulVWLWRCC.rod
VCID: 3A3594B779FA32C617-806E

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 5F: Informationselek. I (J794) Labeldatei:| 5G0-035-MIB-STD2.clb
Teilenummer SW: 5C0 035 680 E HW: 5C0 035 680 E
Bauteil: MU-S-ND-ER H31 0359
Seriennummer: VWZAZ2S5257748
Codierung: 06570001BE00000011111101008808031F0100D4002001004F
Betriebsnr.: WSC 02737 790 50316
ASAM Datensatz: EV_MUStd4CTSAT 001022
ROD: EV_MUStd4CTSAT_VW36.rod
VCID: 231AC6721D49ACA7CF-8076

Datentr‰ger:
Subsystem 1 - Teilenummer SW: 5NA 919 866 BG HW: -----------
Bauteil: ECE AS 2021 --- 1520
Seriennummer: --------------------

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 61: Batterieregelung (J840) Labeldatei:. DRV\1K0-907-534.clb
Teilenummer SW: 7E0 907 534 HW: 7E0 937 090
Bauteil: Batt.regelung H81 0744
Seriennummer: 0982 259161571
Codierung: 030B1A73
Betriebsnr.: WSC 02739 790 00000
VCID: 6867302109E00E98E7-803C

Subsystem 1 - Teilenummer SW: 7E0 915 181 K HW: 7E0 915 181 K
Bauteil: J367-BDMConti H03 1050
Seriennummer: 75410903001609021344

Kein(e) Fehlercode(s) gefunden.

-------------------------------------------------------------------------------
Adresse 6D: Heckklappe (J605) Labeldatei:| DRV\7N0-959-107.clb
Teilenummer SW: 7E0 959 107 HW: 7E0 959 107
Bauteil: HDSG-Modul H01 0652
Revision: 31001001 Seriennummer: 202601186
Codierung: 19730D4002
Betriebsnr.: WSC 01383 790 50316
ASAM Datensatz: EV_HDSGVN46T 203001
ROD: EV_HDSGVN46T.rod
VCID: 6B62362A3DF11CAF8F-803E

Kein(e) Fehlercode(s) gefunden.

Ende----------------------------(Dauer: 04:07)-----------------------------

 

[mmi]

Thanks. German is not a problem

Unfortunately I haven't done this myself. Here is what I have gathered about Thermocall TC3/TC4:

I'm afraid TC3/TC4 does not work with VW OEM heaters - thus reprogramming (flashing) of the heater would be needed for this. It seems that VW OEM heater software doesn't use (Webasto's proprietary) W-bus, instead LIN (Local Interconnect Network) bus is used and obviously between those two protocols there is some discrepancy.​

More here:​

Oem Webasto Auxiliary Heater To Parking Heater "retrofit"

There is one side effect of this "retrofit" - one permanent fault in Aux. Heater (18). 0266 - Databus U1121 00 [009] - Missing Message [TIMEOUT mDachdisplay] Luckily there are no practical consequences of that fault. It appears that connecting Telestart unit without the overhead timer is the...

www.t6forum.com

However,

It seems that OEM heaters equipped with OEM remote controller can be adapted for TC3/TC4 by using an adapter cable (e.g. product number KW1320931A).​

Webasto Adapterkabelbaum für Thermocall TC3 TC4 an Original VW-Touran Tele T91 | eBay

Finden Sie Top-Angebote für Webasto Adapterkabelbaum für Thermocall TC3 TC4 an Original VW-Touran Tele T91 bei eBay. Kostenlose Lieferung für viele Artikel!

www.ebay.de

Y-Adapter Kabelbaum OE - VW/Audi/Skoda

Original Webasto Y-Adapter Kabelbaum OE - VW/Audi/Skoda Lieferumfang: Webasto Y-Adapter Kabelbaum OE - VW/Audi/Skoda Mit diesem Original Webasto Y-Adapterkabelbaum hat man die Möglichkeit, zusätzlich zu dem ab Werk...

www.standheizungs-shop.de

​

However, noticed that your van doesn't have the remote controller. It would have shown in the scan like this:​

-------------------------------------------------------------------------------​

Address 18: Aux. Heat (J364) Labels:| 7E0-963-27X-18.clb​

Part No SW: 7E0 963 272 B HW: 7E0 963 272 B​

Component: STH-T5GP2 003 0009 ​

Coding: 5901​

​

Remote Control Auxiliary Heater: ​

Subsystem 1 - Part No SW: 3Q0 963 513 HW: 3Q0 963 513 ​

Component: R64 D208L 004 0402 ​

-------------------------------------------------------------------------------​

​

 

[Florist]

I'm afraid TC3/TC4 does not work with VW OEM heaters - thus reprogramming (flashing) of the heater would be needed for this. It seems that VW OEM heater software doesn't use (Webasto's proprietary) W-bus, instead LIN (Local Interconnect Network) bus is used and obviously between those two protocols there is some discrepancy.​

Thanks for all the information! Sounds interesting with the LIN / W-Bus and makes sense. So, if I would get the following upgrade kit, the TC3/TC4 should work without the remote controller? You are absolutely right, I don't have one installed. I also don't have the roof controller, which I want to buy.

Webasto Zuheizer - Upgrade Software mit Dongle für VW T6 (bei Aufrüstung zur Standheizung), 249,00 €

Funny thing is, that I can start the heater manually when I connect my VCDS Interface directly with the green/white wire using WTT (Webasto Thermo Test). As far as I know, WTT is also communicating using W-Bus "language". Therefore it is strange that the TC3 isn't working...!?

Thanks for the Y-Wire links. I read over in the German forum, that someone with OEM heater from VW and T91 already installed used one and connected the TC3, which didn't work. But I need to dive deeper in this topic.

Or maybe I just buy a T91 and the roof controller, sell the TC3 and keep everything OEM like

 

[nuttygt4]

I'm a little confused here, I have the overhead panel installed, but I haven't got around to fitting the Telestart unit yet. Am I right in assuming that once I have flashed the heater, the overhead unit will work? If this is the case, where can I find all the bits and bobs to flash the heater, I already have the latest VCDS, but it seems I need another interface and software!

Regards
Graham

 

[Officiallyjeroen]

All required components are already purchased, tested and ready for the installation.

View attachment 61647

View attachment 61648

Well invested €58=£49

My ODIS-E is also ready to upload new(better) firmware

View attachment 61655

Hello there I have a question off course,
Where do you find ore get the latest and New firmware for t6 and rest .

 

[Officiallyjeroen]

As usual my typical show off

Hello again and how did you program the folding mirrors on lock.
I have folding mirrors from factory.
M16.
Thanks keep it up

 

[mmi]

Hello again and how did you program the folding mirrors on lock.
I have folding mirrors from factory.
M16.
Thanks keep it up

How To Program Folding Mirrors - Pictogram

Firstly plug in your VCDS cable. The socket is just below and to the right of the steering column above the accelerator pedal. Then plug the USB end into your PC and start the VCDS application. If this is your first time using the software select Options Then [Test] to make sure the...

www.t6forum.com

 

[Robert]

Hello there I have a question off course,
Where do you find ore get the latest and New firmware for t6 and rest .

Volkswagen AG erWin Online

erwin.volkswagen.de