Lowering And Wheel Alignment Issues?

[CRS Performance]

@CRS Performance

Cheers Steve - your input / comments are really appreciated.
I'm currently sat on -40mm H&R springs fitted by the original converter with standard issue Vw dampers.
At the time it was the best combination I could afford during the van purchase & money pit conversion
All 4.5 years young, at approx 22,000 miles
I'll measure arch gaps as soon as I can, but that will probably be this weekend.

Visually, it definitely sits back end heavy:

View attachment 215951


Don't know if you can remember me, but I'm the T6 driver who has already bought off you H&R arbs, drilled Nutexa discs / pads (front & rear) & have new powder coated 340mm flavour calipers/carriers for the front & the same coloured calipers/carriers for the rears.
Now I've nearly saved up some more GBP's, I'll be calling on your fitting skills early next year to install all, along with whatever flavour new springs & new dampers to suit.
Hopefully your Hunter will be up & working in your new place then, for you to breath your technical expertise (spanners & big hammer) on my Bus?
If the control arm bushes need changing, can these be done at that time or is it best to run over to you to do now?

Our alignment bay is now commissioned , we didn’t go the hunter route , it isn’t flexible enough for some of the low vehicles we want to be checking , and sometimes we do settings outside normal parameters , the new system allows us to program our own settings . It’s brilliant at setting up the power flex adjustable bushes particularly the rear .
we remember your journey so far and compliment you on your patience waiting to get the ARB s fitted. Ha ha

 

[huw169]

I’ve been all over Poole and Bournemouth, even went as far as Southampton to a specialist (yeah right) and I’ve come to the conclusion that nobody down this way has a f***ing clue how to use a Hunter or how to setup adjustable polybushes.

I don’t have the time to go to Bognor and get it done properly, but driving at 12:10 is really pissing me off and no doubt ruining another set of tyres

I use Denmead Tyre Services. Bit of a trek for you but maybe worth a call if you are struggling. My tyre wear is very even and I’m down about 60-65mm.

 

[Insert Coin]

I use Denmead Tyre Services. Bit of a trek for you but maybe worth a call if you are struggling. My tyre wear is very even and I’m down about 60-65mm.

Thanks, might be worth a trip, although that’s about halfway to Bognor Motors.

 

[BognorMotors]

I’ve been all over Poole and Bournemouth, even went as far as Southampton to a specialist (yeah right) and I’ve come to the conclusion that nobody down this way has a f***ing clue how to use a Hunter or how to setup adjustable polybushes.

I don’t have the time to go to Bognor and get it done properly, but driving at 12:10 is really pissing me off and no doubt ruining another set of tyres

We look forward to seeing you soon. Kettle is always on ;-)

 

[sim0n_parker]

Our alignment bay is now commissioned , we didn’t go the hunter route , it isn’t flexible enough for some of the low vehicles we want to be checking , and sometimes we do settings outside normal parameters , the new system allows us to program our own settings . It’s brilliant at setting up the power flex adjustable bushes particularly the rear .
we remember your journey so far and compliment you on your patience waiting to get the ARB s fitted. Ha ha

There isn’t anything that is suitable for the height you have unfortunately . It would have to be developed and because we don’t do those super low drops we wouldn’t invest time and money into that.

Hang on a moment..

Now correct me if I’m wrong, jumping from one post to another post. You are saying to one person that you don’t invest time and money into developing due to you not doing those “super low” drops, yet you had to go out and spend money (investing correct me if I’m wrong??) into an alignment machine to be checking low vehicles.

Mate, you should get yourself a job as a politician with some of the porkies you’ve been firing out over the forum and Facebook.

 

[Insert Coin]

Not really fair, there’s lowered which you’d probably say goes 30-50mm, low which is 50-80mm and super low which is beyond that.

 

[kiidrockk]

I have a T6.1. T32 LWB, 40mm H&R lowering springs.
After installation, at 3000 miles, the combined toe of the rear wheels was 0degr/13min and camber left rear -1degr/44min, right rear -1degr/54min.

The rear tires had some increased wear on the inside after 17 000miles, from mostly highway (this is not my photo, similar wear).

Currently at 60,000 miles, the combined toe of the rear wheels is 0degr/15min and camber left rear -2degr/02min, right rear -2degr/43min.

Is it enough to just replace the outer bushings with adjustable Powerflex bushings to correct the camber?