Search results for query: grommet

I just left mine out, is that a bad idea?

Removed these 4 grommets on the tailgate to check if they were holding water. All clear so put them back in....

Thanks mate…..found the hole with the grommet once I got the tailgate up with VCDS, the lining stops just above the hole, probably for that reason! New handle is on the way so that should solve it. 🤞🏻🙏

...I had a similar problem a few years back. If you didn’t have the van lined, there would be a hole on the inside of the door with a rubber grommet in it. Circled in yellow below. If you poke your finger through said hole, there’s a small lever circled in red, that mechanically operates the...

OK. Resurrecting a very old thread. As per the title really. My plan is to run a cable through the passenger seat grommet under the belly pans to terminate in an Anderson SB50 connector which I can use to connect my fridge so it can sit in the awning or maybe USB lighting. Ideally this will be...

...My electronic tailgate release has stopped working and I cannot get the tailgate to release using the handle. There doesn’t seem to be grommet hiding a keyhole on the handle anywhere and I have no way of opening it from the inside, being a camper the door is ply and carpet lined and there is...

So, for completeness, and to help others, the large grommet circled in the first post doesn’t provide a cable route through into the offside rear quarter. The grommet just behind the rear wheel is the one to use. I’ve run a cable through from inside the rear quarter and out to the tow bar...

Just sent em a message, their profiles are for tin-tops from what I can see, but I've asked their advice. I may just put a 10mm hole in the centre of where I'd like to fit it and see what's what. I can always stick a grommet back in there and seal it with some 522 if I don't like what I find.

Seat Belt Restraints Something I forgot to add was that I also placed some foam around the seat belt fixings to the frame as they are free to move and mean metal rattling against metal. I cut a small square of foam, put a hole in the centre to go around the bolt and then a cut to allow...

Here's the driver's side grommet on mine. My fingertip is hovering over it. It's fairly low down, roughly level height wise with the OS engine mount.

Took a couple of pictures whilst routing through a few wires down from the drivers side A pillar and into the engine bay. Used the grommet behind the dash that goes through to the scuttle area on the drivers side. The grommet is more or less in line with the torx screw as shown in the second...

...top, but due to the bolts, the side flaps will not go in further that the first bolt so trim your sides flaps accordingly. (Pics 5, 6, 7) Grommets I know this has been covered before, the grommets on my seat had pushed out of position and one was damaged. I think this is caused by pushing...

I'll stick them all in here when I'm done.... What a pain in the backside it was getting cables through the tailgate grommet and down the side of the tailgate. All in, it's taken me about a month so far so clear your calendar when you go for it 😁

Yeah I wish I had done it his - squeezing 2 wires though the grommet has left little space for anything else should I want to run cables in. Maybe if I ever take the carpet out again I’ll bring negative inside.

...under the carpet into the channels that are there, as the bolts push it down tight. Pulling the carpet up also gave me access to the rubber grommet without taking out the glove box - I came into the cab from the engine bay. It’s a fiddly but totally possible DIY job! Heated seats are fine...

I’ve searched and read mention of a cable route in through from the rear behind the bumper using an existing grommet. Does anyone know if the grommet circled in the pic (not my van, just a convenient pic taken from the Forum) provides a cable route through and into the offside rear quarter, or...

These Rabone steel tape threading tools come up from time to time on eBay and at car boot sales. I’ve had my metal mouse since the 1970s. They’re worth their weight in gold.

...any distance unconstrained and goes everywhere except where you want it! My next 2 challenges are getting from the bottom of the A-pillar out to the engine bay and getting from the rear cupboard to below the rear bumper. I’ve found posts showing grommets, but have still to investigate in person.

...Recently had the front seats out with all the matting due to a previous owner/convertor putting the EHU lead through the AC drain pipe/grommet so had to dry it all out, and did some sound deadening while it was stripped out (seats, mats, lower dash). Everything else works (lights, door locks...

Omg I can’t believe anyone fitted that c rail like that. I would paint the holes. Then put some rubber grommets.