Search results for query: cable under passenger seat

Looking to install the alpine sub and amp under the driver seat in my T6.1. There is a fuse block under the passenger seat where the heated seat cable goes and it looks like there are some spare female connectors on the plug. Does anyone know if this can be used to power the amp or does it need...

I have a 6 way 12v fusebox under my passenger seat. I would like to run a 40amp cable to the back of the van to run a few simple lights and a water pump (5amp). Can I run this from my one remaining point on the fusebox with a large fuse to secondary 4 way fusebox? Thanks

As @Drive Wayne says. I have exactly the same DC-DC under my passenger seat too and 3 cables to attach the Ablemail. It took longer to change the settings on the Ablemail than it did to fit it!

Yes, swings and roundabouts with the full width fully sliding rear seat/bed :) In my set-up, I can fix the Bluetti power station against the driver's side wall just in front of the wheel arch (SWB). All I need then is a lead run to a permanent connector in the rear plate of the driver seat...

Yes I thought about that, but then you'll still need a cable from a 12v socket to the battery - unless you reckon on charging this at home beforehand and then it lasting for the entirety of your trip. I did this in my previous van (Caddy) and it worked OK, but am thinking now I'd like to install...

Hi, new member, first post... so I installed an under seat amp the other day and used the large red cable under the passenger bench seat to power it. In my infinite newbie wisdom I cut the large red cable just below the point where two smaller red cables were attached to it and securely taped...

Thanks chaps, I couldn't find a spade to fit the top 12V fuse socket so I'm taking the more recommended route and running a wire to the leisure fuses under the passenger seat. Waiting for piggy back to arrive as none of the free fuse sockets under passenger seat are wired to anything, so I need...

Hi all I can say is off my experience really as I needed to wire a led swamper light at the front in the bulk head you will see a rubber boot that goes inside the van I took out the vent on the passenger side and routed the wires with a relay and switch to the battery on its own fuse , my wiring...

Hey @Dellmassive I'm using this as A guide and I'm about to start my installation. I have the factory Aux setup under the passenger seat. I'm going to use the existing wiring from my engine battery into the MPPT/DCDC controller. Do I also need to run a new negative cable from the controller all...

Hi mate. New here. Can I ask you a question? I have a oem split charge. Trying to clear all cables from under the seat. I’m fitting a new dc to dc charger and wondering the best place to take the cable, is it best to wire straight back to the battery or cut and join on to the incoming cable...

Ok thanks for info Yes, would probably get cables made up, as don’t need them longer than they need to be. It was just that the guy installing all the electrics recommended having inverter under passenger seat with battery, then having all the chargers across to drivers seat base? , then I...

My build is progressing slowly - kombi as daily and two kids so edging towards the BIG STUFF. I’ve got 2 amps under the the single passenger seat and just about finished a battery/b2b charger build completed under the driver’s seat. I have a primary midi-fuse box alongside the battery but not...

A couple of reasons, 1) I have used the under floor channels to pass cables to between the passenger and drivers seat (plan to add a second battery at some point) and 2) I also have replaced the original seats with Audi Q8 S-Line ones which are electric and have heating, so come with the same...

The sensor is fixed to the bottom of the sump. The cable on my van traced back up into the cab under the front passenger footwell. I had to remove seat and lift mat to gain access for repair.

Hi all Got a kit from pf jones, I've ran all the cables including the ones to the bcm but struggling with the ones for under passenger seat, it's says the grey white cable for rear fogs in the light blue connector but mine is grey white in a green connector with rear fogs on its...

" Renogy 1000w inverter under drivers seat, and connect to the 160ah lithium which will be under passenger seat, " - this is how i have mine setup. you need to use super beefy cable, as above use the cable guide. 1000w full load will easily pull 100A/120A . . . so cable for that and fuse...

i used 16mm / 20mm copex (split or not) tubing, and run the 16/25mm2 cable in that. along the groves in the bodywork, +++++++++++++++ pics from @Deaky van but you can see there are two low section where the seat base bolt are. . i pushed the tube allong there, green being the feed in...

My Sargent EC155 isn't charging the Fogstar Lithium battery. I've checked the 15amp charger fuse on the Sargent and all the switches are up on the breaker. Read another post on here that says probably easier to install a direct charge solution as, the charger function of the Sargent is...

Got to love an autocorrect! I’ve got it wrong far too many times. The thread unfortunately has not gone where I was hoping! Anyhow, back to the cables. Don’t go playing with the various coloured connectors. As said they are original and can cause issues if disconnected and power applied. I...

Hi, posted a question in the Electrics thread but will try here as I have a T6.1 Birchover. My electrics are currently completely standard but I'm planning to swap out my SCR for a Victron Orion XS DC to DC this week, ready to go Lithium in the near future (will de-rate the amps to 20A or so for...