Search results for query: water ingress

So water ingress then...

Hi - D

Hi All, I’ve spent the weekend messing around with my Vibe door speaker, working out how water gets in, where it goes and how to prevent it. I certainly don’t have a definitive answer, but I’ve made a video compiling information I’ve accrued, which will hopefully help people understand what the...

Driving near home tonight and had to drive through some moderately deep water - not anything to be concerned about for water ingress, but both sides of the road were submerged and there was traffic heading both ways. I was driving through at a sensible speed, maybe 8mph, when the van felt as...

I would put money on the button not the fuse. I think mine got water ingress from roof rail install. You can pick them up from VW or online not to expensive.

I cant find the original poster who commented on putting some material where the arrow goes to stop water ingress. Does anyone know what and where to put said material ? I dont have upgraded speakers but am getting water in the seal when opening the door.. Any help appreciated.

Apply weatherproof flexible sealant to the fixing when refitting as they can allow water ingress, no surprise to most Transporter owners!

Water ingress somewhere. (Prob engine bay areas) Let it dry out. . Reset all the codes. See is the same happens next time it's wet.... If so investigate further.

Hi, sorry the late response. I never got it sorted as such, VW said that water ingress is normal hence why there are drainage holes. The way I've tried to tackle it is by diverting the water that runs down between the C pillar and the sliding door. I stuck a short piece of self adhesive...

Hi all. We have just purchased our first vw T6.1 and there is wet in the compartment at the back where the gas is stored. We have spoke to the garage that converted it and they are saying it’s from the spray off the tyre coming up through the vent. But the carpet is soaking. Surely this isn’t...

Thanks both. Looking at the number of threads online about failures of some element or the other, I’d say it is pretty common! Yes, I often have the tailgate open in wet weather. So could well be water ingress. Garage fitted it both times and no mention was made of any sign of water.

Mine was a control module in the driver's side back corner,just below back light. Mine had corroded with water ingress .

Either way the control module is inside the rear quarter panel above/behind the wheel arch It’s not uncommon for rain to get through the sliding door rail bolts and leak inside the rear quarter panel area so could just be simple water ingress ?

...eliminates the fault. Is there anyone near you willing to meet up? I had a problem with the door locking switches failing intermittently, then completely. It was the microswitch circuit inside the control panel that had suffered water ingress. Might be a good (and relatively easy) place to start.

roof rails are a usual culprit

Pretty sure it’s a x500 model. My speakers have failed (again), this time for good I assume. Water ingress I gather. They are rainbow audio but I can’t find the speakers anywhere so gonna have to get a new set. What model? Also I appear to have damaged the hard plastic bit on my sub, something...

Hi mate don't suppose you know the part number of that controller? I have the exact same issue on my van with the same door. And is it located in the little pocket above the wheel arch? I've had a quick look but could only seem to see a motor in mine.

Is it a genuine part? I guess these are easily damaged and it could have been replaced at some point. If you had the van from new and know you’ve never replaced it then I’m stumped. Water ingress and mould might be an issue but even then you’d expect some reflection I’d have thought?

Your multi rail mount screws are an issue, which will cause water ingress. Replace the missing one and tighten the other for starters. The awning bracket has rivnuts riveted into the bodywork and the M6 Allen bolts are bolted through the bracket and into them. Try tightening the bolts up first...

...anchor points. I have had a bed system installed for the last few years so haven't got ant bolts for the now vacant holes in the tie down points. Guessing I can just get some M10 x 16mm bolts and put in the vacant holes, secure with Loctite and a rubber washer and that should stop water ingress?