Search results for query: 31347

Is that used or new ?

If you want to sell on the forum you need to upgrade your membership to VIP and post a 'For Sale' thread in the appropriate sub-forum.

Have you tried other security codes for module 09 so you can make thechanges in adaptions. Ross Tech has the following: 9-Cent. Elect.31347 20107 42013

Thanks Robert.

It turns out to be a very simple tweak on a T6.1 :cool: Basically open your bonnet/hood. Connect to 09, use SECURITY ACCESS 31347, select ADAPTATION and open channel: change the value from ACTIVE to NOT ACTIVE. That's it, job done.

Confirmed for Crafter. The same thing, open your bonnet/hood. Connect to 09, use SECURITY ACCESS 31347, select ADAPTATION and open channel: change the value from ACTIVE to NOT ACTIVE.

Try this. Go into [09] Central Electronics Security Access and enter 31347 Adaptations: (2)-Acknowledgement Signals -Akustische Rueckmeldung verriegeln (7)-Acknowledgement Signals -Menuesteuerung akustische Rueckmeldung Next check LOCKING menu in settings and make sure that the...

Ensure the bonnet is unlatched. Go to 09 Central Electrics, Security Access Code, 31347, click do it, Go into Adaptions, search Modus, (Type into search box) Pick spaegellersallung funk (excuse my spelling). Then select from the drop down list, by-lock-command via remote control key.

Thanks, I will see how I go. Cheers.

...for a general orientation and can vary greatly depending on the model (motorisation / equipment). If necessary, fewer or further control units will have to be adapted. →Encoding EZE_09 (electronic central electric controller): Access authorisation: 31347 “ Encoding hitch_ecu ->...

...G2 only available here in Argentina and Brazil. Tried those 3 codes spacing time between them to avoid getting locked and didn't work ( 31347, 20107, 42013 ) but they're seems to be rejected due to being wrong. The engine is the well known DDXE (3.0L V6 258/272ps + ZF 8HP70) Just uploaded...

...List -> 69 Trailer hitch control module -> installed Encoding EZE_09 (electronic central electric controller): Access authorisation: 31347 Adaptation -10 Adaptation channel: networking trailer connection device -> installed Trailer hitch control module -> installed Encoding DIS_13 (distance...

...to fully lift the bonnet, just pull the lever so the dash shows the bonnet is open) 09 - Central Electrics Click security access code (input 31347) Click Adaptations Search for modus then select the lower of the two options: ( "by_ convenience_operation_via_remote_control_key" "by_look...

What exactly you mean not working? What's the response of the controller? Have you tried coding without using a code? Based on the scan the SFD/SFD2 is not onboard your Amarok. For the Auto-Scan please use "Save" (not the Print) to make the log more readable. I'm afraid the controller 42 is...

Thank you for you advice, much appreciated. I will give it another go tomorrow. Getting late here in Australia.

Please share (1) full VCDS Auto-Scan, (2) blockmap of 09-Central Electrics (3) adaptation map of 09-Central Electrics

...in year T6.1 2023 Multivan coding/adaptation alterations are locked by bonnet latch and PIN/SA code (Security Access) (which most likely is 31347) So, yes, the bonnet needs to open, or just unlatched. You enter the SA code just before diving into Adaptations - I would guess the OBD11 was...

So I managed to install the wiring and coded it and I believe it is all working (can see trailer on screen when in reverse), indicators and brakes work on trailer board however I do have the following errors on the screen now. Please check brake fluid level. (Consult vehicle wallet.) Please...

Here’s what I have.

Ok. A question: It seems the light switch in position OFF when blockmap-09 was captured - because the following were logged? Please verify the switch is in position Auto and redo the 09-blockmap. IDE05742-IDE02515Light switch position-Low beamNot operated IDE05742-IDE05323Light switch...